Skip to content

Aerospace Grinding Efficiencies with cBN Superabrasives

By Andrew Biro Norton Saint-Gobain

Cubic Boron Nitride (cBN) is a superabrasive material that has traditionally been used to grind materials, such as steels and nickel alloys. Though not as hard as diamond (4500kg/mm2 vs 9000 kg/mm2, respectively) cBN has the benefit of not being as chemically reactive with ferrite-based and nickel alloys and as such, can often outperform diamond-based grinding wheels in terms of life, material removal rates, and lower temperatures.

In fact, a study by Hitchiner and Wilks in 1987 showed that when grinding nickel, the chemical wear of a diamond single point turning tool exceeded the abrasive mechanical wear by a factor of 105, thus highlighting the importance of using cBN in these applications.

One common application for using cBN grinding wheels is on nickel-based superalloys in the aerospace industry. These superalloys are being used in next-generation aircraft engines, driven by good thermal stability at high engine operating temperatures.

Grinding Ni-based superalloys is often done with either conventional aluminum oxide abrasive or with cBN superabrasive wheels. There are many benefits to using cBN: fewer wheel changes and machine down time, low and controlled wear rates, and excellent thermal stability. As with any grinding wheel, the cBN superabrasive wheels wear with use. The wear rate and wear mechanisms are large drivers in determining final wheel performance.

Structure

To understand the wear mechanisms in single layer cBN wheels, it is first important to understand their construction. Single-layer wheels typically consist of a steel core that has been machined or ground to a specific size and tolerance. Next, wheels are masked to keep only the abrasive regions exposed and the cBN grains are then tacked in place. The wheels are then submerged in an electrolytic solution, and a current is passed through the wheel and solution, which draws the Ni-based bond onto the wheel as a cathodic reaction occurs. The thickness of the bond layer is proportional to the amount of time the wheel is plated.

This plating thickness plays a significant role in the wear mechanisms of the cBN grain during grinding. Thicker coatings tend to hold grains at the expense of material removal rate (due to lower grit protrusion from the top surface of the bond) and higher grinding temperatures (due to less room for coolant to enter and grinding swarf to escape). Thinner coatings can be used to increase grit protrusion, at the risk of grain pullout, macro-fracture, and lower wheel life.

Wear Mechanisms

Experts Mike Hitchiner, Stephen Malkin, R. Upadhyaya and Wenfeng Ding agree there are four main possible modes of wear in grinding with electroplated products:

  • Attritious wear of the grains (grain flattening)
  • Grain micro-fracture (microcrystalline splintering)
  • Grain macro-fracture or large scale cleaving (partial grain break-off)
  • Grain/bond interface wear or bond wear (causing total grain breakoff)

In attritious wear, grain wear is very minimal and is concentrated at very small scales around the cutting surfaces. Grinding forces are often insufficient to cause grain fracture and hence dulling results.

This can lead to an increase in the power draw and is often associated with more plowing and rubbing between the grains and work material, leading to a higher likelihood of thermal damage. To combat attritious grain wear, an increase in grinding forces (more aggressive grinding parameters) should be used to promote grain fracture. In dressable products (i.e. vitrified or resin-bonded wheels), dressing parameters and frequency can be used to help combat attritious grain wear as well.

Micro-fracture is the process by which grinding forces are sufficient to cause small scale grain fracture, resulting in continuous generation of sharp cutting points. This is often accompanied by steady-state grinding power. Grain micro-fracture is favorable for a consistent, predictable grinding process.

Macro-fracture occurs when the forces are substantially high, causing larger scale grain cleavage or partial grain breakoff. This typically results in low wheel life, and is an indication that the grinding parameters are too aggressive.

Grain pullout in electroplated products is not common, but can happen if the grain exposure level (i.e. percentage of the grain that is above the plating bond material) is high (>50%) and the forces are high. In grain pullout, the grains are ripped out of the bond, resulting in low wheel life. This was discussed by Ghosh and Chattopadhyay who highlighted the relationship between plating thickness and tendency for grit pullout.

Performance Characteristics

Assuming a grinding process has been developed that results predominantly in micro-fracture of the cBN grains, some common wheel performance trends are often observed with single-layer wheels. The wheel wear and grinding power of a new plated wheel tend to increase quickly during a “break-in” period, where only the tips of the highest grains are cutting the material, leading to a lower active grit density and rougher surface.

However, this break-in period is often very short, and gives way to a more stable grinding process where rates of change for wheel wear, power and surface finish can decrease by up to 10X the initial break in rates. Wheel failure tends to occur once the grains have dulled and worn, causing grinding power to increase and surface roughness to drop, often resulting in workpiece burn. Failure can also be caused by grain and bond stripping off of the steel core (in more aggressive applications). In both failure modes, predicting the end of life is difficult, and is best estimated using empirical life data from previous wheels.

Troubleshooting

The final performance of the wheel in a grinding application is only partially a function of the wheel. Other factors can have significant influence and should also be evaluated when troubleshooting, including coolant system filtration, setup and nozzles, machine stiffness and forces, and the fixture of the workpiece. It is important to remember that the final stress-state of the abrasive grain is a culmination of both thermal and mechanical wear, which are driven by machine parameters, coolant, and lubricity. Once the entire system has been evaluated, focus may be placed on designing a grind cycle that promotes micro-fracture and self-sharpening wheels, which should lead to improved wheel performance and a more consistent, repeatable process.

  • Latest Videos

  • Connect With SME Media

Related Articles

  • Boeing 737

    After 737 Max, Boeing Separates CEO, Chairman Jobs

    October 12, 2019
    Boeing Co.'s 737 Max crisis just had another impact on the aircraft maker -- its board opted to separate the jobs of chief executive officer and chairman. The company announced the move on Friday. CEO Dennis Muilenburg no longer is chairman of the board.
    By Bill Koenig - Senior Editor, SME Media
  • Larry Marchand
    Expert Opinion

    The Future Flight Path of Aerospace Technology

    October 1, 2019
    In today’s aerospace industry, manufacturers often feel bound to operate a certain way because it’s a tried-and-true, validated process or because the physics of aerospace dictate certain limitations on materials, systems and designs.
    By Larry Marchand - Vice President, Sales Profile Division, United Grinding North America Inc.
  • Aerospace Grinding Efficiencies with cBN Superabrasives

    Aerospace Grinding Efficiencies with cBN Superabrasives

    September 17, 2019
    Cubic Boron Nitride (cBN) is a superabrasive material that has traditionally been used to grind materials, such as steels and nickel alloys. Though not as hard as diamond cBN has the benefit of not being as chemically reactive with ferrite-based and nickel alloys.
    By Andrew Biro, Norton Saint-Gobain

Webinars, White Papers and More!

SME's Manufacturing Resource Center keeps you updated on all of the latest industry trends and information. Access unlimited FREE webinars, white papers, eBooks, case studies and reports now!