Skip to content

For Those Scrutinizing Weight of Cars and Trucks, the Marathon Continues

Bill Koenig
By Bill Koenig Senior Editor, SME Media

Motorized vehicle builders are making progress dropping pounds, but there’s no finish line in sight

The Management Briefing Seminars, organized by the Center for Automotive Research (CAR) in Ann Arbor, MI, is a summer tradition in the auto industry. Professionals gather outside of the northwest Michigan resort town of Traverse City to examine industry issues.

12-A-robot-welds-the-final-assembly-of-a-crash-management-system.-Constellium-White-GA-300x187.jpg
A robot welds the final assembly of a crash management system with aluminum parts at Constellium’s plant in White, GA.

At this year’s edition, one of the most frequent issues discussed was making cars and trucks lighter. The industry has been under regulatory pressure for years to boost fuel efficiency and cut emissions. Now, pressure is intensifying as the industry faces the prospects of making more electric vehicles and gasoline-electric hybrids to meet toughening regulations.That’s because consumers have “range anxiety” concerning how far electric vehicles can travel between charges.

“With electric vehicles, every ounce counts,” said Richard Chung, vice president of innovation at Adient, a German supplier of automotive interiors.

Chung was among those attending the seminars. Lightweighting, he said, remains a priority in automotive.

“OEMs are putting a lot of pressure on us,” he said. “We’ve gotten as efficient as possible with traditional steel products.” Now, he said, Adient is looking at new materials, including high-strength steels, increased use of plastic and composite materials.

This decade, automakers, working closely with suppliers, have reduced the weight of their vehicles—in some cases by hundreds of pounds.

Besides using a greater variety of materials, OEMs and suppliers have found new ways to join together parts made with different materials. Lightweighting is such a part of the industry that the CAR gathering includes the Altair Enlighten Award. It recognizes company efforts to cut vehicle weight. This year’s winners included FCA US LLC for its redesigned Pacifica (which trimmed 113 kg following a redesign), Toyota Motor Corp. and supplier Faurecia.

Pressure rises

However, the hard part is just starting.

The industry has to continue the momentum, going deeper into vehicles and components to find weight savings. The industry, while doing all that, has to balance safety and customer demand for more vehicle features.

“Pressure is on the engineer to get weight out,” Jay Baron, president of CAR, said in an interview prior to the conference.

“What is happening, the pressure to reduce is forcing the industry to reduce the margin of error,” he said. “Are we going to lightweight to be less safe? The issue of crash worthiness is huge.”

Some companies, amid their lightweighting efforts, discover unanticipated problems.

Mahle Industries, while developing lighter weight automotive components, found that some pistons and piston rings could crack unpredictably. Engines are getting smaller while being equipped with turbochargers to maintain power. Thus, there’s more strain.

“This is about downsizing,” Joachim Wagenblast, director of product development for engine systems and components in North America for Mahle, said at a June media briefing by auto suppliers. “Downsizing is about lightweighting. You have to get more power out of a smaller combustion chamber.”

“You have to make these products more robust,” he said in a follow-up interview in July. “You increase the wall thickness of some areas. You develop new coatings.”

Downsizing limits

There are also limits, in some cases, to how quickly vehicles can go on a diet.

General Motors Co. has achieved its biggest weight reductions following major vehicle redesigns, including new “architectures.” Lighter materials for component designs were included as part of the process.

For example, the company reduced the weight of its GMC Acadia by 700 lb (322 kg).

“We could pull out all the stops,” said Rob Peckham, GM technical integration engineer for mass strategy and tools. “Every bit of learning could be put in there. We’re not going to make a major architecture change every other year. To get mass out, you have to make major investments.”

US regulators, in rules set in 2012, set a target for the US vehicle fleet to average 54.5 mpg (23 km/l) by the 2025 model year.

Achieving that target has been complicated by consumers buying more (and heavier) trucks than regulators anticipated. The Trump administration said in March it was reviewing the target, set during the Obama administration. It is not known how the review may affect the standards.

New R&D center

Given the lead times for developing vehicles, automakers and suppliers are proceeding with their efforts to cut weight of vehicles.

For example, the Spanish firm Gestamp Automocion SL has opened a new North American R&D center in Auburn Hills, MI. Lightweighting will be one of the major tasks for the facility. The company estimates that body and structural parts comprise more than half of a vehicle’s weight.

“We want to be a global player,” said Paul Belanger, Gestamp’s director of R&D for North America. “We have to be close to where you develop” new vehicles. Gestamp customers include GM, Ford Motor Co., FCA and Honda Motor Co.

Gestamp previously co-developed with Honda a rear rail system made from high-strength steel for the automaker’s Civic. Energy from a crash is absorbed by system components.

“We worked collaboratively with Honda,” Belanger said. “That supports the need to build a North American R&D center. We were [previously] limited in R&D” in North America.

The new R&D facility has an area of 3425 m2 and has 45 employees, with plans to expand to 64 employees by the end of the year. It has crash-simulation capabilities for body in white components and testing equipment for chassis components.

“We try to look at all of the emerging technologies,” Belanger said. “There is not a single answer” to lightweighting.

Expanding business

Constellium, an aluminum products maker, has expanded its automotive business because of lightweighting.

The Netherlands-based company supplies Ford and BMW. It operates a plant in Van Buren Township, MI, and has opened a new 135,000 ft2 (12,540 m2) operation in White, GA.

Its offerings include a one-piece aluminum extrusion windshield header, which replaced a five-piece steel assembly.

At the Michigan plant, such parts are bent so they can be attached to a vehicle. The parts are then heat-treated to increase their strength. The factory also makes aluminum components for crash-management systems designed to fold up and absorb energy in accidents.

Eric Krepps, the company’s vice president and general manager for Constellium Automotive Structures North America, said automakers will “combine parts and remove parts. We’ve done this with customers, it allows you to eliminate cost and weight.”

The company also sees electric vehicles as an opportunity.

Regulators in California, the largest vehicle market in the US, and nine other states require sales of electric vehicles to reduce emissions. One concern with EVs is their range between charges.

“Driving distance is directly related to the weight of a car, the mass of the car,” said John Biel, engineering director for Constellium Automotive Structures North America.

“We still see many, many opportunities,” said Paul Warton, president of Constellium’s Automotive Structures unit, who attended the CAR event in Traverse City.

‘Civilized explosive welding’

It’s not just automakers and suppliers who are drawn to lightweighting issues.

There are academic studies related to the issue.

For example, researchers at The Ohio State University are studying “civilized explosive welding” as a way to join dissimilar materials and avoid corrosion.

With the process, a thunderbolt rams one material into another to create a welded joint.

“It’s an early stage technology we’re committed to,” Glenn Daehn, professor of metallurgical engineering for the university, said in February at the Lightweight Vehicle Manufacturing Summit in Detroit.

“We think this is the best way to join advanced or dissimilar materials,” he said.

Also involved are two institutes that are part of Manufacturing USA, a program set up under the Obama administration for academic institutions, nonprofits and companies to collaborate on manufacturing technology.

The two working on lightweighting are Lightweight Innovations for Tomorrow (LIFT) and the Institute for Advanced Composites Manufacturing Innovation (IACMI). IACMI has a satellite office at LIFT’s headquarters.

Equipment has been installed this year at LIFT after the 100,000 ft2 (9290 m2) headquarters building’s electrical system was rewired. One large piece of equipment is a linear friction welder, that’s 60 × 40′ with a 9′ foundation (18 × 12 and 2.7-m deep). There will also be a “beta area” where machine makers can demonstrate new models for as long as six months.

Manufacturing USA institutes are meant to develop new manufacturing technology to the point that firms can commercialize them. LIFT members have participated in a series of projects, including one for an automotive differential that’s 50% lighter, according to the institute.

Materials genome initiative

“A lot of our portfolio is going after the 10, 20, 30% improvement,” said Alan Taub, chief technology officer at LIFT.

LIFT also is developing computer modeling to predict how different materials change during manufacturing. It’s dubbed Integrated Computational Materials Engineering, or ICME. It’s more informally known as the Materials Genome Initiative. “The engineers like to call it that,” Taub said. “It’s basically getting materials processing simulation tools fully integrated with product design tools.”

LIFT also is exploring “low investment, agile metalforming technology,” he said.

At IACMI, one of the primary missions is to develop new composite materials and find ways to spread their use in manufacturing. With automotive, IACMI is trying to develop “potential replacement of steel and aluminum with lower-carbon-footprint materials,” said Uday Vaidya, the institute’s chief technology officer.

One IACMI priority, he said, is to develop cheaper forms of carbon fiber that would be cost effective for auto manufacturing. Currently, the material is used in race cars and expensive production models, such as BMW’s i3, Ford’s GT and Honda’s NSX.

“If we can get this into high production, it’s a very big breakthrough,” Vaidya said.

Steel, aluminum industries

Lightweighting remains a high priority for the steel and aluminum industries.

The steel industry has developed high-strength and ultra-high-strength steels, which are strong enough so less of the material is needed compared with conventional steel.

“We’re getting to the limits of the [high-strength] grades available,” said Jody Hall, vice president of the automotive market for the Steel Market Development Institute. “But new steels are being developed.”

One lightweighting issue, she said, is “we have to get more power out of smaller engines. We are studying pistons and crankshafts because of increased performance.”

Hall also said steel will remain in the picture as the industry shifts from steel-dominant to “mixed material” vehicles.

Body in white of vehicles are “almost 100% steel,” she said. “Half of body in white are advanced higher strength steels… Steel is still going to be around with higher penetration of alternate materials in the body.”

The aluminum industry also is optimistic.

“There’s an increasing need for mass reduction,” said Doug Richman, chairman of the technical committee of the transportation group of the Aluminum Association. “It gets more stringent year over year.”

Aluminum previously made inroads in wheels, engines and cylinder blocks, Richman said. “Now the major area is the body. That’s certainly, for the next 10 years, where the growth will be.”

Aluminum’s biggest inroad into vehicle bodies was Ford’s F-150 and Super Duty pickups. The trucks sell at high volume—which justified Ford’s investments in revamping body shops. Also, the trucks are North American products made at a handful of factories.

The marathon continues

Nevertheless, as the industry shifts to multi-material cars and trucks, Richman likes aluminum’s chances.

“There are 300–350 metal parts in a car body,” he said. You look at each individual part and ask what is the material for that part.” Aluminum will win its share of such decisions, he said.

“I feel great,” Richman said. “I’m somewhat relieved.” The aluminum industry, he said, would struggle “if everybody stampeded to all-aluminum vehicles.”

The main certainty is that lightweighting remains a marathon.

“We’re adding more lightweighting technology every year,” said CAR’s Baron. “Regulators have accelerated demand for these lightweighting technologies.”

  • VIEW ALL ARTICLES
  • Connect With Us
    TwitterFacebookLinkedInYouTube

Related Articles

  • Montez King Executive Director NIMS (National Institute for  Metalworking Skills)
    Smart Manufacturing

    New smart training framework works for Industry 4.0 jobs

    July 22, 2020
    The credential hanging on my wall that swells me with pride is my machinist certificate. That apprenticeship experience was the “ON!” switch for my career path. The brightness of that light helped maintain the vision and the hope even as I faced significant racial bias almost 30 years ago.
    By Montez King - Executive Director, NIMS
  • Glenn Nausley President Promess, Inc.
    Smart Manufacturing

    How ‘smart processes’ fit into Industry 4.0

    July 21, 2020
    If Industry 3.0 is identified by the computerization of factory floor processes to make them “smart,” then Industry 4.0 can be understood as the expansion of the idea to include all of the non-factory floor inputs required to produce a quality product and a successful enterprise.
    By Glenn Nausley - President, Promess Inc.
  • Russ Fadel  CEO Augmentir
    Smart Manufacturing

    Bringing the frontline to the forefront of Industry 4.0

    July 21, 2020
    I met a man recently. He had worked at a small manufacturing company for 20 plus years and was the sole technician responsible for the assembly of his company’s most complex product. After years of dedication to the company, he was set to retire.
    By Russ Fadel - CEO, Augmentir

Webinars, White Papers and More!

SME's Manufacturing Resource Center keeps you updated on all of the latest industry trends and information. Access unlimited FREE webinars, white papers, eBooks, case studies and reports now!