Skip to content

Grinding Gamma Titanium Aluminide

By Andrew Biro Applications Engineer, Norton Saint-Gobain
1 TiAl with duplex microstructure.jpg
TiAl with duplex microstructure consisting of γ and lamellar regions

Titanium aluminides possess many characteristics that make them highly attractive for high-temperature structural applications in automotive and aerospace industries. Their high specific strength, high-temperature stability and oxidation resistance relative to conventional titanium and nickel alloys make them beneficial for use in low-pressure turbine blades for aerospace engines, as well as turbochargers and exhaust values in automotive engines.

Titanium aluminides can vary in mechanical and thermal properties based on the annealing temperatures used in processing. Research has shown that among the four different γ-TiAl microstructures that can be obtained by annealing, the duplex microstructure, as shown in the first figure (containing between 45 and 50 atomic% aluminum), is more ductile at room temperatures than others. Therefore, this is the most commonly used microstructure for engineering applications. It consists of two constituents: the gamma (γ) phases which provide strength and the lamellar phases, with alternating layers of α2 and γ phases, which increase toughness.

1b wheels-grit sizes.jpg
Summary of wheels and corresponding abrasive grit sizes tested

Large scale applications of γ-TiAl in aerospace engines began with use of this duplex gamma titanium aluminide material, specifically GE 48Al-2Cr-2NB alloy (commonly designated 48-2-2), in the last two stages of the GEnx engine for the Boeing 787 Dreamliner, which entered service in 2011. Since then, γ-TiAl has found increasing acceptance among engine manufacturers for newer engines. Both the new Pratt and Whitney GTF engines and CFM Leap Engines have different stages composed of γ-TiAl blades in their low pressure turbine areas. The heat resistance typically associated with nickel alloys, alongside the lightweight characteristics of titanium, make γ-TiAl attractive for these engine makers who are striving for increased fuel efficiency and reduced emissions.

Titanium aluminide components are generally very expensive to process and can be two to three times the cost of nickel-based superalloys. Near-gamma alloys are processed through ingot metallurgy, powder metallurgy or casting. The next steps in component fabrication are usually done through some form of machining, grinding or by non-traditional methods such as Electro-discharge Machining, Electro Chemical machining or some combination of these processes. When compared with single-point machining, like with any intermetallic, grinding is often recognized as the best method for achieving final part dimensions and surface characteristics on γ-TiAl components.

2 Setup.jpg
Setup on a creepfeed grinder

Saint-Gobain Abrasives has been researching and developing new grinding technology to use with these intermetallics since 2011 at the state-of-the-art Higgins Grinding Technology Center (HGTC) located in Northboro, Massachusetts. Testing has been in close coordination with its European counterpart, European Grinding Technology Center (EGTC) located in Norderstedt, Germany to meet the global manufacturing needs of the aerospace and automotive industries. The focus of this research is on developing grinding expertise while designing custom-bonded abrasive and superabrasive grinding solutions that are well-suited for efficient and damage-free grinding of components made of γ-TiAl.

Recent product testing on gamma titanium aluminide focused around evaluating three core abrasive types: diamond, cubic boron nitride (cBN) and conventional silicon carbide (SiC). The diamond and cBN products included electroplated and dressable multi-layer metal bonded wheels, while the SiC abrasives were used with a conventional vitrified bond system. For each superabrasive type (i.e. diamond & cBN), two grit sizes were evaluated to better understand the effect of grit size on force, power, and surface roughness of the final components. A summary of the wheels is shown in the first table.

2b Test conditions.jpg
Summary of testing conditions

Testing was conducted by grinding slots, as in the second figure, into blocks of gamma titanium aluminide under two material removal rates in order to evaluate the products in both mild and aggressive grinding conditions. Only one set of grinding conditions was used per slot in order to preserve the ground surfaces for subsequent analysis. Wheels were dressed in between slots (i.e. for each new set of grinding conditions). A summary of the grinding conditions is shown in the second table. Products were evaluated based on power, applied normal forces, part surface finish, and damage in the titanium aluminide components (cracking and/or burn).

The results of this study showed that for the conventional SiC abrasives, the power (and forces) increased as a function of stock removal. Similar trends were also observed for cBN wheels; however, the power increase was much lower than for SiC. The diamond wheels drew the lowest power consistently, and also had the most stable power curve as a function of stock removed. The same trends were observed with the coarser superabrasive wheels (250 um) and the multi-layer superabrasive products relative to the SiC abrasive products.

The increase in power (and forces) in SiC wheels resulted in cracking and mild burn on the surfaces of the ground components. No cracking was observed in the cBN or the diamond wheels after 1800 mm3 of material removal. In fact, the diamond wheels were capable of removing 48000 mm3 of material without damaging the components. The cBN and SiC wheels reached only about 6 and 10% (respectively) of that total value before part damage was observed.

3 grinding power comparison.jpg
Specific grinding power for each of the abrasives tested

The damage in the components was attributed to metal adhesion on the tips of the grains. This adhesion was most prevalent in the SiC wheels. This metal adhesion was also observed on cBN grains, but to a much lower degree than the SiC. Very little metal adhesion was observed on the tips of the diamond grains. The adhesion of the metal to the surfaces has been known to lead to lower grinding efficiency (i.e. higher frictional contributions and a reduced ability for the grains to remove material).

4 images of cracking.jpg
Cracking in a component as ground (left) and using liquid dye penetrant to highlight the cracking (right)

While the diamond products were clearly superior in terms of cumulative stock removal without component damage, individual grinding processes may still dictate the use of SiC products. Processes which require frequent wheel dressing in order to maintain strict form requirements would benefit from using SiC, as the cost/wheel is substantially lower and form can be easily maintained through dressing. Electroplated diamond wheels, while capable of removing substantial amounts of material, are limited in their tolerances. If used to the point where the wheels come out of tolerance, no redressing can be done and the product must be replaced. With the recent development of new, multi-layer dressable metal bond diamond products by Saint-Gobain Abrasives, new possibilities have been opened up with the ability to use these diamond products in applications where form and finish have very strict tolerances which can be maintained over time.

5 SEM of used SiC wheel.jpg
SEM of a used SiC wheel face showing metal adhesion on the tips of the active grains.

The future of γ-TiAl as a prominent material in advanced aerospace engines is looking very good. Newer technologies are constantly being pursued to bring the processing cost of γ-TiAl down to the levels of nickel-based superalloys. This will help to broaden the scope ofγ-TiAl applications. For instance, some groups are successfully fabricating engine parts out of γ-TiAl using Electron-beam based 3D printing. Even these 3D printed γ-TiAl components will still require some form of grinding to generate the final surface. With this in mind, Saint-Gobain Abrasives is continuously striving to provide innovative solutions to grind this material more efficiently to its aerospace customers and OEMs. Recent studies from Saint-Gobain Abrasives document some great advantages with the use of dressable metal-bonded diamond wheels with patented high-porosity (Norton Paradigm) for grinding γ-TiAl. For those customers that prefer conventional wheels instead of superabrasives, new and improved conventional SiC wheels that enable cooler cutting and require lower dressing frequency are also being pursued.

  • View All Articles
  • Connect With Us

Related Articles

Webinars, White Papers and More!

SME's Manufacturing Resource Center keeps you updated on all of the latest industry trends and information. Access unlimited FREE webinars, white papers, eBooks, case studies and reports now!